Toona 24 V

• With the TO4024 motor, you can automate swing gates with leafs measuring up to 3 m long.
• With the TO5024 and TO5024I motors, you can automate swing gates with leafs measuring up to 5 m long.
• With the TO5024HS motor, you can automate swing gates with leafs measuring up to 5 m long or weighing up to 400 kg.
• With the TO6024HS motor, you can automate swing gates with leafs measuring up to 6 m long or weighing up to 1450 kg.
• With the TO7024 motor, you can automate swing gates with leafs measuring up to 7 m long.

If the PS324 backup battery has been installed, the motor will continue to operate even in the event of power failure.

If no backup battery has been installed, release the motor and move the gate manually as shown in the first part of the video.

All the level one programming functions of the control unit are set by default to "OFF" and can be modified at any moment.

Each function is represented by an LED:

• LED L1 automatic closing: the gate closes automatically after the programmed pause time. The pause time is initially set at 30 seconds, but may be modified to 5, 15, 30, 45, 60, 80, 120 or 180 seconds.
• LED L2 close after photo: when the function is active and the photocells are triggered during opening or closing manoeuvres, the pause time is reduced to 5 seconds, regardless of the programmed value.
  When the "automatic closing" function is deactivated, if the photocells are triggered during the closing manoeuvre, "automatic closing" is activated with the programmed pause time.
• LED L3 always close: when the function is active, when power is restored after a blackout, the control unit detects that the gate is open and automatically starts a closing manoeuvre, preceded by 5 seconds of pre-flashing.
  If the function is deactivated, when power is restored following a blackout, the gate remains where it is.
• LED L4 standby (BlueBUS): when the function is active, 1 minute after the end of the manoeuvre, the control unit turns off the BlueBUS output, all devices connected to it and all LEDs except the BlueBUS LED, which flashes more slowly. When the control unit receives a command, it resumes normal operation.
  This function reduces consumption and is recommended when the control unit is powered by batteries or photovoltaic panels.
• LED L5 electric lock / courtesy light: when the function is active, the “electric lock” output becomes the "courtesy light" output. When it is deactivated, the output operates as the "electric lock" output.
• LED L6 pre-flash: when the function is active, it sets a pause of 3 seconds between the moment the flashing light starts flashing and the start of the manoeuvre, to signal a possibly dangerous situation in advance.
  If the function is deactivated, the flashing light starts flashing at the start of the manoeuvre.
• LED L7 close/partial open 1: when the function is active, the "close" input of the control unit becomes "partial open 1".
• LED L8 gate open indicator / maintenance indicator: when this function is active, the "gate open indicator" output becomes "maintenance indicator".
  When the function is deactivated, the output functions as “gate open indicator”.

To access level one programming of the control unit, proceed as follows, respecting the sequence:

1. Press and hold the STOP key until LED L1 starts flashing, then release;
2. Press the OPEN or CLOSE key to move to the LED representing the function you want to modify;
3. Press the STOP key to change the state of the function:
   - a short flash indicates that the function is deactivated (OFF);
   - a long flash indicates that the function is activated (ON).
4. To activate or deactivate other functions, repeat steps 2 and 3, otherwise wait 10 seconds to exit programming mode.

The parameters which can be managed in level two programming are indicated in the following table.

To access level two programming of the control unit, proceed as follows, respecting the sequence:

1. Press and hold the STOP key until LED L1 starts flashing, then release;
2. Press the OPEN or CLOSE key to move to the LED representing the function you want to modify;
3. Press and hold the STOP key: wait for about 3 seconds until the LED representing the current level of the parameter you want to modify comes on; keep pressing the STOP key;
4. Still keeping the STOP key pressed, press the OPEN or CLOSE key to move the LED representing the value of the parameter to the desired level;
5. When the desired level is reached, release the STOP key;
6. To modify other parameters, repeat steps 2, 3, 4 and 5, otherwise wait 10 seconds to exit programming mode.

If a flashing light is connected to the FLASH output of the control unit, while a manoeuvre is underway, it emits one flash every second.

If there is a malfunction, the flashing light emits shorter flashes: these are repeated twice, separated by a one second pause.

• If the LED flashes at a frequency of one flash per second, the control unit is operating normally.
• If the LED is off, check that the control unit is powered. If the control unit is powered, check the fuses have not blown; if there is a blown fuse, replace it with another of the same value.
• If the LED is on steadily, try shutting off power to the control unit. If the condition persists, replace the electronic board.
• If the LED emits two quick flashes, one of the inputs has changed: open, stop, triggering of the photocells or command from the transmitter.

The BlueBUS LED may emit a series of flashes separated by a one second pause. These should be interpreted in the same way as the flashing light (see the specific FAQ).

• If the LED is on, the STOP input is active normally.
• If the LED is off, check the devices connected to the STOP input to identify which of these is active.

• If the LED is off, the PP input is not active.
• If the LED is on, the device connected to the PP input is active.

• If the LED is off, the OPEN input is not active.
• If the LED is on, the device connected to the OPEN input is active.

• If the LED is off, the CLOSE input is not active.
• If the LED is on, the device connected to the CLOSE input is active.

If LEDs L1 and L2 are flashing slowly simultaneously, this means that the number of devices connected to the BlueBUS terminal has varied, or that device self-learning has not been performed. In both cases, device self-learning must be performed.

If LEDs L3 and L4 are flashing slowly simultaneously, this means self-learning of the limit switch positions has not been performed. Adjust the limit switch position.